seville sts ´99 Keele muutmine saksast ingliseks.
seville sts ´99 Keele muutmine saksast ingliseks.
Tervitus. Olen uus ja õnnelik cadillaci omanik. Ainult oleks väksemat sorti mure. Sai auto soetatud saksamaalt ja kogu auto räägib saksa keelt. Kas on seda võimalik muuta inglise keelseks.
ah muidugi - pealkirja ei ole ma veel lugema õppinud :D
Aga jutt ise on selline - see ütleb küll, et sinu aasta pole toetatud, aga mis need mikid ikka teavad - proovida igatahes tasub.
Seal allpool, boldiga osa on see koodide osa, eelnev on õpetus, kuidas sinna jõuda. Kõik saab teha ise ja armatuurilt, kui ei õnnestu, siis on vaja ilmselt servisesse minna ja Tech II aparaati kasutada.
NOTES
THIS ONLY WORKS FOR THE FOLLOWING MODELS!!!
96-02 Eldorado, ETC, ESC
96-97 Seville, STS, SLS
96-99 Deville, Concourse, DeElegance
~~~~~TO ADD COOLANT AND MPH DIC MESSAGE~~~~~
1) Press the OFF and PASS WARMER (referred to from here as WARMER) buttons simultaneously to enter diagnostic mode.
2) Let the system read any codes it has stored. You will ultimately be presented with "PCM?". You will answer with the fan speed control button. UP = yes and DOWN = no.
3) Press DOWN until you are presented with "IPC?". On mine, it's the very next prompt. When you get to the "IPC?" prompt, press UP to enter the IPC area (Instrument Panel Cluster).
4) Press DOWN until you are presented with "IPC OVERRIDE?". Press UP to enter the override area.
5) Scroll down (with the DOWN button) until you get to Option E. Wait a second or two, and the override value will appear to the right where the TRIP ODOMETER normally reads. Yours will probably read "43". That's what mine read when I first did this.
Below are the Option E values:
- Coolant Temp message (64)
- Battery Volts message (32)
- Engine RPM message (16)
- Avg Mph message ( 8 )
- Mph message (4)
- Fuel Used message (2)
- Inst Mpg message (1)
The stock displays (for analog E/K displays) are Battery Volts, Avg Mph, Fuel Used, and Inst Mpg, for a total value of "43".
6) Use the WARMER button to increment the value of the override. In this case, we want to add Coolant Temp, so we're going to add "64" to "43", or "107". Press the WARMER button repeatedly to increment the value from "43" to "107".
If you make a mistake, you can decrement the value by pressing the COOLER button.
7) To permanently save the new value, hold the FRONT DEFROST and the A/C buttons simultaneously until the new override value flashes once.
8 ) You're done. Press OFF repeatedly to "back out" of the diagnostic system. You'll probably need to press OFF 5 or 6 times to get out of the deep "menu structure" you're in now.
Now, the coolant temp (in units specified) should be one "stop" along the revolving door we call the DIC. If you are in metric units, the coolant temp will read in *C. If you are in standard units, it'll read in *F.
~~~~~TO SHUT OFF DRLS~~~~~
1-4 FOLLOW ABOVE DIRECTIONS!!!
5) Scroll down (with the DOWN button) until you get to Option C. Wait a second or two, and the override value will appear to the right where the TRIP ODOMETER normally reads.
Below are the Option C values:
IPS03 Option C
- RSS installed (128)
-Premium Unleaded Fuel Only -
-Graphic supression (digital) (64)
-Daytime running lamps enabled (32)
-Cellular Telephone Installed (16)
-BTSI message suppression (4)
-Options not set (2)
-FUEL LEVEL LOW message suppresion (1)
6) Use the COOLER button to decrease the value of the override. In this case, we want to remove the DRLs so subtract your number by 32
If you make a mistake, you can decrement the value by pressing the WARMER button.
7) To permanently save the new value, hold the FRONT DEFROST and the A/C buttons simultaneously until the new override value flashes once.
8) You're done. Press OFF repeatedly to "back out" of the diagnostic system. You'll probably need to press OFF 5 or 6 times to get out of the deep "menu structure" you're in now.
NOTE!!!!
in order for your drls to ACTUALLY BE OFF your twilight must be pushed all the way to the left and your fog lights (when applicable) must be off as well!!!
HOPE THIS HELPS
heres all the option values in the event anyone wants to play with them for any reason
IPS01 Option A
-Universal Theft Deterrent enabled ( 8 )
-Personalization / Memory Installed (4)
-Interior Purge enabled (1)
IPS02 OPtion B ( EXport Country)
-Eropean Economic Community (EEC) (16)
-Japan ( 8 )
-Saudi Arabia (4)
-Canada (2)
-Norway/ Sweden (1)
IPS03 Option C
-RSS installed (128)
-Premium Unleaded Fuel Only Graphic supression [DIGITAL ONLY] (64)
-Daytime running lamps enabled (32)
-Cellular Telephone Installed (16)
-BTSI message suppression (4)
-Options not set (2)
-FUEL LEVEL LOW message suppresion (1)
IPS04 Option D (HVAC Options)
-Afterblow enabled (128)
-De-Ice Installed (64)
-Timer Recirc enabled (16)
-Dual Zone HVAC Installed ( 8 )
Below are the Option E (DIC features)
- Coolant Temp message (64)
- Battery Volts message (32)
- Engine RPM message [DIGITAL ONLY] (16)
- Avg Mph message ( 8 )
- Mph message (4)
- Fuel Used message (2)
- Inst Mpg message (1)
Anna siis teada, kuidas välja tuli....
Aga jutt ise on selline - see ütleb küll, et sinu aasta pole toetatud, aga mis need mikid ikka teavad - proovida igatahes tasub.
Seal allpool, boldiga osa on see koodide osa, eelnev on õpetus, kuidas sinna jõuda. Kõik saab teha ise ja armatuurilt, kui ei õnnestu, siis on vaja ilmselt servisesse minna ja Tech II aparaati kasutada.
NOTES
THIS ONLY WORKS FOR THE FOLLOWING MODELS!!!
96-02 Eldorado, ETC, ESC
96-97 Seville, STS, SLS
96-99 Deville, Concourse, DeElegance
~~~~~TO ADD COOLANT AND MPH DIC MESSAGE~~~~~
1) Press the OFF and PASS WARMER (referred to from here as WARMER) buttons simultaneously to enter diagnostic mode.
2) Let the system read any codes it has stored. You will ultimately be presented with "PCM?". You will answer with the fan speed control button. UP = yes and DOWN = no.
3) Press DOWN until you are presented with "IPC?". On mine, it's the very next prompt. When you get to the "IPC?" prompt, press UP to enter the IPC area (Instrument Panel Cluster).
4) Press DOWN until you are presented with "IPC OVERRIDE?". Press UP to enter the override area.
5) Scroll down (with the DOWN button) until you get to Option E. Wait a second or two, and the override value will appear to the right where the TRIP ODOMETER normally reads. Yours will probably read "43". That's what mine read when I first did this.
Below are the Option E values:
- Coolant Temp message (64)
- Battery Volts message (32)
- Engine RPM message (16)
- Avg Mph message ( 8 )
- Mph message (4)
- Fuel Used message (2)
- Inst Mpg message (1)
The stock displays (for analog E/K displays) are Battery Volts, Avg Mph, Fuel Used, and Inst Mpg, for a total value of "43".
6) Use the WARMER button to increment the value of the override. In this case, we want to add Coolant Temp, so we're going to add "64" to "43", or "107". Press the WARMER button repeatedly to increment the value from "43" to "107".
If you make a mistake, you can decrement the value by pressing the COOLER button.
7) To permanently save the new value, hold the FRONT DEFROST and the A/C buttons simultaneously until the new override value flashes once.
8 ) You're done. Press OFF repeatedly to "back out" of the diagnostic system. You'll probably need to press OFF 5 or 6 times to get out of the deep "menu structure" you're in now.
Now, the coolant temp (in units specified) should be one "stop" along the revolving door we call the DIC. If you are in metric units, the coolant temp will read in *C. If you are in standard units, it'll read in *F.
~~~~~TO SHUT OFF DRLS~~~~~
1-4 FOLLOW ABOVE DIRECTIONS!!!
5) Scroll down (with the DOWN button) until you get to Option C. Wait a second or two, and the override value will appear to the right where the TRIP ODOMETER normally reads.
Below are the Option C values:
IPS03 Option C
- RSS installed (128)
-Premium Unleaded Fuel Only -
-Graphic supression (digital) (64)
-Daytime running lamps enabled (32)
-Cellular Telephone Installed (16)
-BTSI message suppression (4)
-Options not set (2)
-FUEL LEVEL LOW message suppresion (1)
6) Use the COOLER button to decrease the value of the override. In this case, we want to remove the DRLs so subtract your number by 32
If you make a mistake, you can decrement the value by pressing the WARMER button.
7) To permanently save the new value, hold the FRONT DEFROST and the A/C buttons simultaneously until the new override value flashes once.
8) You're done. Press OFF repeatedly to "back out" of the diagnostic system. You'll probably need to press OFF 5 or 6 times to get out of the deep "menu structure" you're in now.
NOTE!!!!
in order for your drls to ACTUALLY BE OFF your twilight must be pushed all the way to the left and your fog lights (when applicable) must be off as well!!!
HOPE THIS HELPS
heres all the option values in the event anyone wants to play with them for any reason
IPS01 Option A
-Universal Theft Deterrent enabled ( 8 )
-Personalization / Memory Installed (4)
-Interior Purge enabled (1)
IPS02 OPtion B ( EXport Country)
-Eropean Economic Community (EEC) (16)
-Japan ( 8 )
-Saudi Arabia (4)
-Canada (2)
-Norway/ Sweden (1)
IPS03 Option C
-RSS installed (128)
-Premium Unleaded Fuel Only Graphic supression [DIGITAL ONLY] (64)
-Daytime running lamps enabled (32)
-Cellular Telephone Installed (16)
-BTSI message suppression (4)
-Options not set (2)
-FUEL LEVEL LOW message suppresion (1)
IPS04 Option D (HVAC Options)
-Afterblow enabled (128)
-De-Ice Installed (64)
-Timer Recirc enabled (16)
-Dual Zone HVAC Installed ( 8 )
Below are the Option E (DIC features)
- Coolant Temp message (64)
- Battery Volts message (32)
- Engine RPM message [DIGITAL ONLY] (16)
- Avg Mph message ( 8 )
- Mph message (4)
- Fuel Used message (2)
- Inst Mpg message (1)
Anna siis teada, kuidas välja tuli....
Ikka on mingi jama. Mul pole selliseid nuppegi soendusel nagu siin jutt käib näit OFF nupp. Võibolla olen ise juhe aga mul ei õnnestunud. :|
https://www.mygmlink.com/pdf/go2content ... eville.pdf
lehekülg 146 on minu auto lülitite pilt.
https://www.mygmlink.com/pdf/go2content ... eville.pdf
lehekülg 146 on minu auto lülitite pilt.