Cadillac Club Estonia

1947
Engine Specifications: 1947 Cadillac 346 V8
GENERAL SPECIFICATIONS
Model Designation: Series 60S, Series 61, Series 62, Series 75
Wheel base: Series 60S: 133; Series 61: 126; Series 62: 129; Series 75: 136
Valve Location: In block
Bore and Stroke: 3-1/2 x 4-1/2
Piston displacement, Cubic Inches: 346.0
Compression ratio: 7.25
Maximum Brake Horsepower: 150 @ 3400 RPM
Maximum Torque Lbs.Ft. @ RPM: 260 @ 1700 RPM
Normal Oil Pressure Pounds: 30
TUNE UP SPECIFICATIONS (all models)
Spark Plug Make: AC 104
Spark Plug Gap, Inch: .030
Firing Order: 18736542 (front to rear: Right bank 2-4-6-8, left bank 1-3-5-7)
Timing Mark: IGN, location: Vib. Damper
Engine Idle Speed, RPM: Standard transmission: 375; w/automatic 375 (in drive)
Cylinder Head Torque Lbs.Ft.: 70-75
Compression Pressure & Cranking Speed: 105
Voltage & Polarity: 6 volts, negative ground
PISTON AND RING SPECIFICATIONS
Fitting Pistons with Scale: Pistons removed from above. Shim thickness: .002
Pounds on a Pull Scale: 11
Ring End Gap: In tapered bores, fit rings in tightest portion of ring travel
Compression: .007
Oil: .007
Clearance in Groove: Compression: .0022-0035; Oil: .0015-.003
Wristpin Diameter, Inch: .875
VALVE SPECIFICATIONS
Operating Clearance:
Intake: 0 Exhaust: 0
Valve Seat Angle, degrees: 45
Valve Timing: (BTDC = before top dead center; ATDC = after top dead center)
Intake opens: Top Dead Center
Exhaust Closes: 10 ATDC
Valve Spring Pressure Pounds at Inches Length:
Inner Spring: 66 @ 1-59/64
Valve Stem Clearance: Intake: .001-.003; Exhaust: .002-.004
ENGINE BEARING SPECIFICATIONS
Connecting Rod Bearings:
Journal Diameter, Inches: 2.4590-2.4595
Bearing Clearance, Inch: .0005-.002
Rod End Play, Inch: .008-.014
Rod Bolt Tension: Lbs.Ft.: 60-65
Main Bearings:
Journal Diameter, Inches: 2.4990-2.4995
Bearing clearance: .0008-.0025
Shaft End Play: .001-.005 (Thrust on Number 2 Bearing)
Main Bolt Tension: Lbs.Ft.: 130-140
CAPACITY DATA
Cooling System:
Without heater: 25 quarts
Without heater: 25; with heater: 26
Fuel Tank: All models except 75: 20 gallons; Model 75: 24 gallons
Engine Oil: 7 quarts
Transmission: w/out overdrive: 2-1/2 pints; Automatic: 12 quarts
Rear Axle: 5 pints
DELCO-REMY DISTRIBUTOR SPECIFICATIONS
Distributor part number: 1110807 (distributor rotates clockwise)
Cam Angle, degrees: 21-30
Breaker Point opening, Inch: .016
Condenser Capacity: .18-.23 Mfds.
Breaker Arm Spring Tension: 19-23 Oz.
Centrifugal Advance: (degrees at RPM of distributor)
Advance starts: 1/2 @ 500 RPM
Full Advance: 12 @ 2000 RPM
Inches of Vacuum to Start Plunger Movement: 5-7
Inches of Vacuum for Full Plunger Movement: 15-18
Maximum Vacuum Advance Dist., Degrees: 9
DELCO-REMY GENERATOR SPECIFICATIONS
Generator Number: 1102693 (generator rotates clockwise, 6 volts, Negative Ground)
Generator output: 36 amps @ 3500 RPM
Brush Spring Tension: 25 oz.
DELCO-REMY REGULATOR SPECIFICATIONS
Regulator Number: 1118242
Cutout Relay:
Voltage to close points: 6.4
Reverse current to open points: 0-3
Voltage Regulator Setting: 7.4 volts
Current and Voltage Armature Air Gap: .075 inches
Current Regulator Setting: 36 amps
DELCO-REMY STARTING MOTOR SPECIFICATIONS
Part number: 1107931 (rotates clockwise)
Bush Spring Tension, Ounces: 24-28
No Load Test: 65 amps, 5 volts @ 5500 RPM
Torque Test: 600 Amps, 3.0 volts, Torque, Lbs.Ft.: 16
WHEEL ALIGNMENT SPECIFICATIONS
Caster, Degrees
Limits: -1-3/4 to - 2-3/4
Desired: - 2-1/4
Camber, Degrees
Limits: -3/8 to +3/8
Desired: 0
Toe-In, Inches: 1/32 to 3/32
Toe-Out on Turns, Degrees: (If toe-out is incorrect, when other adjustments are correct, look for bent steering arms.)
Outer wheel: 20
Inner Wheel: 24-1/2 to 25-1/4; Models 67 & 75: 23-1/2 to 24-1/2
Kingpin Angle, or Steering Axis Degrees: (If king pin or spindle support angle are incorrect, but camber is correct, look for bent suspension arms or steering knuckle support)
5-5/6 @ 04 Camber

1948
Engine Specifications: 1948 Cadillac 346 V8
GENERAL SPECIFICATIONS
Model Designation: Series 60S, Series 61, Series 62, Series 75
Wheel base: Series 60S: 133; Series 61: 126; Series 62: 126; Series 75: 136
Valve Location: In block
Bore and Stroke: 3-1/2 x 4-1/2
Piston displacement, Cubic Inches: 346.0
Compression ratio: 7.25
Maximum Brake Horsepower: 150 @ 3400 RPM
Maximum Torque Lbs.Ft. @ RPM: 260 @ 1700 RPM
Normal Oil Pressure Pounds: 30
TUNE UP SPECIFICATIONS (all models)
Spark Plug Make: AC 104
Spark Plug Gap, Inch: .030
Firing Order: 18736542 (front to rear: Right bank 2-4-6-8, left bank 1-3-5-7)
Timing Mark: IGN, location: Vib. Damper
Engine Idle Speed, RPM: Standard transmission: 375; w/automatic 375 (in drive)
Cylinder Head Torque Lbs.Ft.: 70-75
Compression Pressure & Cranking Speed: 105
Voltage & Polarity: 6 volts, negative ground
PISTON AND RING SPECIFICATIONS
Fitting Pistons with Scale: Pistons removed from above. Shim thickness: .002
Pounds on a Pull Scale: 11
Ring End Gap: In tapered bores, fit rings in tightest portion of ring travel
Compression: .007
Oil: .007
Clearance in Groove: Compression: .0022-0035; Oil: .0015-.003
Wristpin Diameter, Inch: .875
VALVE SPECIFICATIONS
Operating Clearance:
Intake: 0 Exhaust: 0
Valve Seat Angle, degrees: 45
Valve Timing: (BTDC = before top dead center; ATDC = after top dead center)
Intake opens: Top Dead Center
Exhaust Closes: 10 ATDC
Valve Spring Pressure Pounds at Inches Length:
Inner Spring: 66 @ 1-59/64
Valve Stem Clearance: Intake: .001-.003; Exhaust: .002-.004
ENGINE BEARING SPECIFICATIONS
Connecting Rod Bearings:
Journal Diameter, Inches: 2.4590-2.4595
Bearing Clearance, Inch: .0005-.002
Rod End Play, Inch: .008-.014
Rod Bolt Tension: Lbs.Ft.: 60-65
Main Bearings:
Journal Diameter, Inches: 2.4990-2.4995
Bearing clearance: .0008-.0025
Shaft End Play: .001-.005 (Thrust on Number 2 Bearing)
Main Bolt Tension: Lbs.Ft.: 130-140
CAPACITY DATA
Cooling System:
Without heater: 25 quarts
Without heater: 25; with heater: 26
Fuel Tank: All models except 75: 20 gallons; Model 75: 24 gallons
Engine Oil: 7 quarts
Transmission: w/out overdrive: 2-1/2 pints; Automatic: 12 quarts
Rear Axle: 5 pints
DELCO-REMY DISTRIBUTOR SPECIFICATIONS
Distributor part number: 1110807 (distributor rotates clockwise)
Cam Angle, degrees: 21-30
Breaker Point opening, Inch: .016
Condenser Capacity: .18-.23 Mfds.
Breaker Arm Spring Tension: 19-23 Oz.
Centrifugal Advance: (degrees at RPM of distributor)
Advance starts: 1/2 @ 500 RPM
Full Advance: 12 @ 2000 RPM
Inches of Vacuum to Start Plunger Movement: 5-7
Inches of Vacuum for Full Plunger Movement: 15-18
Maximum Vacuum Advance Dist., Degrees: 9
DELCO-REMY GENERATOR SPECIFICATIONS
Generator Number: 1102693 (generator rotates clockwise, 6 volts, Negative Ground)
Generator output: 36 amps @ 3500 RPM
Brush Spring Tension: 25 oz.
DELCO-REMY REGULATOR SPECIFICATIONS
Regulator Number: 1118242
Cutout Relay:
Voltage to close points: 6.4
Reverse current to open points: 0-3
Voltage Regulator Setting: 7.4 volts
Current and Voltage Armature Air Gap: .075 inches
Current Regulator Setting: 36 amps
DELCO-REMY STARTING MOTOR SPECIFICATIONS
Part number: 1107931 (rotates clockwise)
Bush Spring Tension, Ounces: 24-28
No Load Test: 65 amps, 5 volts @ 5500 RPM
Torque Test: 600 Amps, 3.0 volts, Torque, Lbs.Ft.: 16
WHEEL ALIGNMENT SPECIFICATIONS
Caster, Degrees
Limits: -1/2 to +1/2
Desired: 0
Camber, Degrees
Limits: -3/8 to +3/8
Desired: 0
Toe-In, Inches: 1/16 to 1/8
Toe-Out on Turns, Degrees: (If toe-out is incorrect, when other adjustments are correct, look for bent steering arms.)
Outer wheel: 20
Inner Wheel: 24-1/2 to 25-1/2; Model 75: 23-1/2 to 24-1/2
Kingpin Angle, or Steering Axis Degrees: (If king pin or spindle support angle are incorrect, but camber is correct, look for bent suspension arms or steering knuckle support)
5-5/6 @ 04 Camber

1949
Engine Specifications: 1949 Cadillac 331 V8
GENERAL SPECIFICATIONS
Model Designation: Series 60S, Series 61, Series 62, Series 75
Wheel base: Series 60S: 133; Series 61: 126; Series 62: 126; Series 75: 136
Valve Location: In head
Bore and Stroke: 3-13/16 x 3-5/8
Piston displacement, Cubic Inches: 331.0
Compression ratio: 7.50
Maximum Brake Horsepower: 160 @ 3800 RPM
Maximum Torque Lbs.Ft. @ RPM: 312 @ 1800 RPM
Normal Oil Pressure Pounds: 35
TUNE UP SPECIFICATIONS (all models)
Spark Plug Make: AC 48X
Spark Plug Gap, Inch: .035
Firing Order: 18436572 (front to rear: Right bank 2-4-6-8, left bank 1-3-5-7)
Timing Mark: "A" mark for premiurm fuel; "C" mark for regular fuel; location: Vib. Damper
Engine Idle Speed, RPM: Standard transmission: 375; w/automatic 375 (in drive)
Cylinder Head Torque Lbs.Ft.: 65-70
Compression Pressure & Cranking Speed: 140
Voltage & Polarity: 6 volts, negative ground
PISTON AND RING SPECIFICATIONS
Fitting Pistons with Scale: Pistons removed from above. Shim thickness: .002
Pounds on a Pull Scale: 11
Ring End Gap: In tapered bores, fit rings in tightest portion of ring travel
Compression: .007
Oil: .007
Clearance in Groove: Compression: .0022-0035; Oil: .0015-.003
Wristpin Diameter, Inch: 1.000
VALVE SPECIFICATIONS
Operating Clearance:
Intake: 0 Exhaust: 0
Valve Seat Angle, degrees: 44
Valve Timing: (BTDC = before top dead center; ATDC = after top dead center)
Intake opens: 15 BTDC
Exhaust Closes: 40 ATDC
Valve Spring Pressure Pounds at Inches Length:
Inner Spring: 60 @ 1-11/16
Valve Stem Clearance: Intake: .001-.0025; Exhaust: .0015-.0035
ENGINE BEARING SPECIFICATIONS
Connecting Rod Bearings:
Journal Diameter, Inches: 2.2488-2.2493
Bearing Clearance, Inch: .0005-.002
Rod End Play, Inch: .008-.014
Rod Bolt Tension: Lbs.Ft.: 40-45
Main Bearings:
Journal Diameter, Inches: 2.4990-2.4995
Bearing clearance: .0008-.0025
Shaft End Play: .001-.005 (Thrust on Rear Bearing)
Main Bolt Tension: Lbs.Ft.: 90-100
CAPACITY DATA
Cooling System:
Without heater: 18 quarts
With heater: 19
Fuel Tank: 20 gallons
Engine Oil: 5 quarts
Transmission: w/out overdrive: 2-1/2 pints; Automatic: 12 quarts
Rear Axle: 5 pints
DELCO-REMY DISTRIBUTOR SPECIFICATIONS
Distributor part number: 1110812 (distributor rotates counter-clockwise)
Cam Angle, degrees: 21-30
Breaker Point opening, Inch: .016
Condenser Capacity: .18-.23 Mfds.
Breaker Arm Spring Tension: 19-23 Oz.
Centrifugal Advance: (degrees at RPM of distributor)
Advance starts: 3/4 @ 300 RPM
Full Advance: 18-3/4 @ 1800 RPM
Inches of Vacuum to Start Plunger Movement: 6-8
Inches of Vacuum for Full Plunger Movement: 14
Maximum Vacuum Advance Dist., Degrees: 9
DELCO-REMY GENERATOR SPECIFICATIONS
Generator Number: 1102700 (generator rotates clockwise, 6 volts, Negative Ground)
Generator output: 45 amps @ 3500 RPM
Brush Spring Tension: 25 oz.
DELCO-REMY REGULATOR SPECIFICATIONS
Regulator Number: 1118357
Cutout Relay:
Voltage to close points: 6.4
Reverse current to open points: 0-3
Voltage Regulator Setting: 7.3 volts
Current and Voltage Armature Air Gap: .075 inches
Current Regulator Setting: 42 amps
DELCO-REMY STARTING MOTOR SPECIFICATIONS
Part number: 1107945 (rotates clockwise)
Bush Spring Tension, Ounces: 24-28
No Load Test: 65 amps, 5 volts @ 5500 RPM
Torque Test: 600 Amps, 3.0 volts, Torque, Lbs.Ft.: 16
WHEEL ALIGNMENT SPECIFICATIONS
Caster, Degrees
Limits: -1/2 to +1/2
Desired: 0
Camber, Degrees
Limits: -3/8 to +3/8
Desired: 0
Toe-In, Inches: 1/16 to 1/8
Toe-Out on Turns, Degrees: (If toe-out is incorrect, when other adjustments are correct, look for bent steering arms.)
Outer wheel: 20
Inner Wheel: 24-1/2 to 25-1/2; Model 75: 23-1/2 to 24-1/2
Kingpin Angle, or Steering Axis Degrees: (If king pin or spindle support angle are incorrect, but camber is correct, look for bent suspension arms or steering knuckle support)
5-5/6 @ 04 Camber

1950
Engine Specifications: 1950 Cadillac 331 V8
GENERAL SPECIFICATIONS
Model Designation: Series 60S, Series 61, Series 62, Series 75
Wheel base: Series 60S: 130; Series 61: 122; Series 62: 126; Series 75: 146-1/2
Valve Location: In head
Bore and Stroke: 3-13/16 x 3-5/8
Piston displacement, Cubic Inches: 331.0
Compression ratio: 7.50
Maximum Brake Horsepower: 160 @ 3800 RPM
Maximum Torque Lbs.Ft. @ RPM: 312 @ 1800 RPM
Normal Oil Pressure Pounds: 35
TUNE UP SPECIFICATIONS (all models)
Spark Plug Make: AC 48X
Spark Plug Gap, Inch: .035
Firing Order: 18436572 (front to rear: Right bank 2-4-6-8, left bank 1-3-5-7)
Timing Mark: "A" mark for premiurm fuel; "C" mark for regular fuel; location: Vib. Damper
Engine Idle Speed, RPM: Standard transmission: 375; w/automatic 375 (in drive)
Cylinder Head Torque Lbs.Ft.: 65-70
Compression Pressure & Cranking Speed: 120 min.
Voltage & Polarity: 6 volts, negative ground
PISTON AND RING SPECIFICATIONS
Fitting Pistons with Scale: Pistons removed from above. Shim thickness: .002
Pounds on a Pull Scale: 11
Ring End Gap: In tapered bores, fit rings in tightest portion of ring travel
Compression: .010
Oil: .010
Clearance in Groove: Compression: .0017-0035; Oil: .0015-.003
Wristpin Diameter, Inch: 1.000
VALVE SPECIFICATIONS
Operating Clearance:
Intake: 0 Exhaust: 0
Valve Seat Angle, degrees: 44
Valve Timing: (BTDC = before top dead center; ATDC = after top dead center)
Intake opens: 14 BTDC
Exhaust Closes: 24 ATDC
Valve Spring Pressure Pounds at Inches Length:
Inner Spring: 60 @ 1-11/16
Valve Stem Clearance: Intake: .001-.0025; Exhaust: .0015-.0035
ENGINE BEARING SPECIFICATIONS
Connecting Rod Bearings:
Journal Diameter, Inches: 2.2488-2.2493
Bearing Clearance, Inch: .0005-.002
Rod End Play, Inch: .008-.014
Rod Bolt Tension: Lbs.Ft.: 40-45
Main Bearings:
Journal Diameter, Inches: 2.4990-2.4995
Bearing clearance: .0008-.0025
Shaft End Play: .001-.005 (Thrust on Rear Bearing)
Main Bolt Tension: Lbs.Ft.: 90-100
CAPACITY DATA
Cooling System:
Without heater: 18 quarts
With heater: 19
Fuel Tank: 20 gallons
Engine Oil: 5 quarts
Transmission: w/out overdrive: 2-1/2 pints; Automatic: 12 quarts
Rear Axle: 5 pints
DELCO-REMY DISTRIBUTOR SPECIFICATIONS
Distributor part number: 1110819 (distributor rotates counter-clockwise)
Cam Angle, degrees: 24-30
Breaker Point opening, Inch: .016
Condenser Capacity: .18-.23 Mfds.
Breaker Arm Spring Tension: 19-23 Oz.
Centrifugal Advance: (degrees at RPM of distributor)
Advance starts: 3/4 @ 300 RPM
Full Advance: 16 @ 1800 RPM
Inches of Vacuum to Start Plunger Movement: 4-6
Inches of Vacuum for Full Plunger Movement: 12-16
Maximum Vacuum Advance Dist., Degrees: 10
DELCO-REMY GENERATOR SPECIFICATIONS
Generator Number: 1102700 (generator rotates clockwise, 6 volts, Negative Ground)
Generator output: 45 amps @ 3500 RPM
Brush Spring Tension: 25 oz.
DELCO-REMY REGULATOR SPECIFICATIONS
Regulator Number: 1118357
Cutout Relay:
Voltage to close points: 6.4
Reverse current to open points: 0-3
Voltage Regulator Setting: 7.3 volts
Current and Voltage Armature Air Gap: .075 inches
Current Regulator Setting: 42 amps
DELCO-REMY STARTING MOTOR SPECIFICATIONS
Part number: 1107969 (rotates clockwise)
Bush Spring Tension, Ounces: 24-28
No Load Test: 60 amps, 5 volts @ 6000 RPM
Torque Test: 600 Amps, 3.0 volts, Torque, Lbs.Ft.: 15
WHEEL ALIGNMENT SPECIFICATIONS
Caster, Degrees
Limits: -1/2 to +1/2
Desired: 0
Camber, Degrees
Limits: -3/8 to +3/8
Desired: 0
Toe-In, Inches: 1/16 to 1/8
Toe-Out on Turns, Degrees: (If toe-out is incorrect, when other adjustments are correct, look for bent steering arms.)
Outer wheel: 20
Inner Wheel: 24-1/2 to 25-1/2; Model 75: 23-1/2 to 24-1/2
Kingpin Angle, or Steering Axis Degrees: (If king pin or spindle support angle are incorrect, but camber is correct, look for bent suspension arms or steering knuckle support)
5-5/6 @ 04 Camber

1951
Engine Specifications: 1951 Cadillac 331 V8
GENERAL SPECIFICATIONS
Model Designation: Series 60S, Series 61, Series 62, Series 75
Wheel base: Series 60S: 130; Series 61: 122; Series 62: 126; Series 75: 147
Valve Location: In head
Bore and Stroke: 3-13/16 x 3-5/8
Piston displacement, Cubic Inches: 331.0
Compression ratio: 7.50
Maximum Brake Horsepower: 160 @ 3800 RPM
Maximum Torque Lbs.Ft. @ RPM: 312 @ 1800 RPM
Normal Oil Pressure Pounds: 35
TUNE UP SPECIFICATIONS (all models)
Spark Plug Make: AC 48X
Spark Plug Gap, Inch: .035
Firing Order: 18436572 (front to rear: Right bank 2-4-6-8, left bank 1-3-5-7)
Timing Mark: "A" mark for premiurm fuel; "C" mark for regular fuel; location: Vib. Damper
Engine Idle Speed, RPM: Standard transmission: 375; w/automatic 375 (in drive)
Cylinder Head Torque Lbs.Ft.: 65-70
Compression Pressure & Cranking Speed: 120 min.
Voltage & Polarity: 6 volts, negative ground
PISTON AND RING SPECIFICATIONS
Fitting Pistons with Scale: Pistons removed from above. Shim thickness: .002
Pounds on a Pull Scale: 11
Ring End Gap: In tapered bores, fit rings in tightest portion of ring travel
Compression: .010
Oil: .010
Clearance in Groove: Compression: .0017-0035; Oil: .0015-.003
Wristpin Diameter, Inch: 1.000
VALVE SPECIFICATIONS
Operating Clearance:
Intake: 0 Exhaust: 0
Valve Seat Angle, degrees: 44
Valve Timing: (BTDC = before top dead center; ATDC = after top dead center)
Intake opens: 14 BTDC
Exhaust Closes: 24 ATDC
Valve Spring Pressure Pounds at Inches Length:
Inner Spring: 60 @ 1-11/16
Valve Stem Clearance: Intake: .001-.0025; Exhaust: .0015-.0035
ENGINE BEARING SPECIFICATIONS
Connecting Rod Bearings:
Journal Diameter, Inches: 2.2488-2.2493
Bearing Clearance, Inch: .0005-.002
Rod End Play, Inch: .008-.014
Rod Bolt Tension: Lbs.Ft.: 40-45
Main Bearings:
Journal Diameter, Inches: 2.4990-2.4995
Bearing clearance: .0008-.0025
Shaft End Play: .001-.005 (Thrust on Rear Bearing)
Main Bolt Tension: Lbs.Ft.: 90-100
CAPACITY DATA
Cooling System:
Without heater: 18 quarts
With heater: 19
Fuel Tank: 20 gallons
Engine Oil: 5 quarts
Transmission: w/out overdrive: 2-1/2 pints; Automatic: 12 quarts
Rear Axle: 5 pints
DELCO-REMY DISTRIBUTOR SPECIFICATIONS
Distributor part number: 1110820 (distributor rotates counter-clockwise)
Cam Angle, degrees: 28-34
Breaker Point opening, Inch: .016
Condenser Capacity: .18-.23 Mfds.
Breaker Arm Spring Tension: 19-23 Oz.
Centrifugal Advance: (degrees at RPM of distributor)
Advance starts: 3/4 @ 300 RPM
Full Advance: 16 @ 1800 RPM
Inches of Vacuum to Start Plunger Movement: 4-6
Inches of Vacuum for Full Plunger Movement: 13-15
Maximum Vacuum Advance Dist., Degrees: 10
DELCO-REMY GENERATOR SPECIFICATIONS
Generator Number: 1102700 (generator rotates clockwise, 6 volts, Negative Ground)
Generator output: 45 amps @ 3500 RPM
Brush Spring Tension: 25 oz.
DELCO-REMY REGULATOR SPECIFICATIONS
Regulator Number: 1118357
Cutout Relay:
Voltage to close points: 6.4
Reverse current to open points: 0-3
Voltage Regulator Setting: 7.3 volts
Current and Voltage Armature Air Gap: .075 inches
Current Regulator Setting: 42 amps
DELCO-REMY STARTING MOTOR SPECIFICATIONS
Part number: 1107969 (rotates clockwise)
Bush Spring Tension, Ounces: 24-28
No Load Test: 60 amps, 5 volts @ 6000 RPM
Torque Test: 600 Amps, 3.0 volts, Torque, Lbs.Ft.: 15
WHEEL ALIGNMENT SPECIFICATIONS
Caster, Degrees
Limits: -1/2 to +1/2
Desired: 0
Camber, Degrees
Limits: -3/8 to +3/8
Desired: 0
Toe-In, Inches: 1/16 to 1/8
Toe-Out on Turns, Degrees: (If toe-out is incorrect, when other adjustments are correct, look for bent steering arms.)
Outer wheel: 20
Inner Wheel: 24-1/2 to 25-1/2; Model 75: 23-1/2 to 24-1/2
Kingpin Angle, or Steering Axis Degrees: (If king pin or spindle support angle are incorrect, but camber is correct, look for bent suspension arms or steering knuckle support)
5-5/6 @ 04 Camber

1952
Engine Specifications: 1952 Cadillac 331 V8
GENERAL SPECIFICATIONS
Model Designation: Series 60S, Series 62, Series 75
Wheel base: Series 60S: 130; Series 62: 126; Series 75: 146-3/4
Valve Location: In head
Bore and Stroke: 3-13/16 x 3-5/8
Piston displacement, Cubic Inches: 331.0
Compression ratio: 7.50
Maximum Brake Horsepower: 190 @ 4000 RPM
Maximum Torque Lbs.Ft. @ RPM: 322 @ 2400 RPM
Normal Oil Pressure Pounds: 35
TUNE UP SPECIFICATIONS (all models)
Spark Plug Make: AC 48X
Spark Plug Gap, Inch: .035
Firing Order: 18436572 (front to rear: Right bank 2-4-6-8, left bank 1-3-5-7)
Timing Mark: "A" mark for premiurm fuel; "C" mark for regular fuel; location: Vib. Damper
Engine Idle Speed, RPM: Standard transmission: 450; w/automatic 400 (in drive)
Cylinder Head Torque Lbs.Ft.: 65-70
Compression Pressure & Cranking Speed: 142
Voltage & Polarity: 6 volts, negative ground
PISTON AND RING SPECIFICATIONS
Fitting Pistons with Scale: Pistons removed from above. Shim thickness: .002
Pounds on a Pull Scale: 11
Ring End Gap: In tapered bores, fit rings in tightest portion of ring travel
Compression: .010
Oil: .010
Clearance in Groove: Compression: .0017-0035; Oil: .0015-.003
Wristpin Diameter, Inch: 1.000
VALVE SPECIFICATIONS
Operating Clearance:
Intake: 0 Exhaust: 0
Valve Seat Angle, degrees: 44
Valve Timing: (BTDC = before top dead center; ATDC = after top dead center)
Intake opens: 14 BTDC
Exhaust Closes: 24 ATDC
Valve Spring Pressure Pounds at Inches Length:
Inner Spring: 60 @ 1-11/16
Valve Stem Clearance: Intake: .001-.0025; Exhaust: .0015-.0035
ENGINE BEARING SPECIFICATIONS
Connecting Rod Bearings:
Journal Diameter, Inches: 2.2488-2.2493
Bearing Clearance, Inch: .0005-.002
Rod End Play, Inch: .008-.014
Rod Bolt Tension: Lbs.Ft.: 40-45
Main Bearings:
Journal Diameter, Inches: 2.4990-2.4995
Bearing clearance: .0008-.0025
Shaft End Play: .001-.005 (Thrust on Rear Bearing)
Main Bolt Tension: Lbs.Ft.: 90-100
CAPACITY DATA
Cooling System:
Without heater: 19 quarts
With heater: 20 quarts
Fuel Tank: 20 gallons
Engine Oil: 5 quarts
Transmission: w/out overdrive: 2-1/2 pints; Automatic: 12 quarts
Rear Axle: 5 pints
DELCO-REMY DISTRIBUTOR SPECIFICATIONS
Distributor part number: 1110829 (distributor rotates counter-clockwise)
Cam Angle, degrees: 28-34
Breaker Point opening, Inch: .016
Condenser Capacity: .18-.23 Mfds.
Breaker Arm Spring Tension: 19-23 Oz.
Centrifugal Advance: (degrees at RPM of distributor)
Advance starts: 3/4 @ 340 RPM
Full Advance: 17 @ 1850 RPM
Inches of Vacuum to Start Plunger Movement: 7-9
Inches of Vacuum for Full Plunger Movement: 16-1/2
Maximum Vacuum Advance Dist., Degrees: 11
DELCO-REMY GENERATOR SPECIFICATIONS
Generator Number: 1102781 (generator rotates clockwise, 6 volts, Negative Ground)
Generator output: 50 amps @ 3500 RPM
Brush Spring Tension: 25 oz.
DELCO-REMY REGULATOR SPECIFICATIONS
Regulator Number: 1118725
Cutout Relay:
Voltage to close points: 6.4
Reverse current to open points: 0-4
Voltage Regulator Setting: 7.3 volts
Current and Voltage Armature Air Gap: .075 inches
Current Regulator Setting: 47 amps
DELCO-REMY STARTING MOTOR SPECIFICATIONS
Part number: 1107969 (rotates clockwise)
Bush Spring Tension, Ounces: 24-28
No Load Test: 60 amps, 5 volts @ 6000 RPM
Torque Test: 600 Amps, 3.0 volts, Torque, Lbs.Ft.: 15
WHEEL ALIGNMENT SPECIFICATIONS
Caster, Degrees
Limits: -1/2 to +1/2
Desired: 0
Camber, Degrees
Limits: -3/8 to +3/8
Desired: 0
Toe-In, Inches: 1/16 to 1/8
Toe-Out on Turns, Degrees: (If toe-out is incorrect, when other adjustments are correct, look for bent steering arms.)
Outer wheel: 20
Inner Wheel: 24-1/2 to 25-1/2; Model 75: 23-1/2 to 24-1/2
Kingpin Angle, or Steering Axis Degrees: (If king pin or spindle support angle are incorrect, but camber is correct, look for bent suspension arms or steering knuckle support)
5-5/6 @ 04 Camber

1953
Engine Specifications: 1953 Cadillac 331 V8
GENERAL SPECIFICATIONS
Model Designation: Series 60S, Series 62, Series 75
Wheel base: Series 60S: 130; Series 62: 126; Series 75: 146-3/4
Valve Location: In head
Bore and Stroke: 3-13/16 x 3-5/8
Piston displacement, Cubic Inches: 331.0
Compression ratio: 8.25
Maximum Brake Horsepower: 210 @ 4150 RPM
Maximum Torque Lbs.Ft. @ RPM: 330 @ 2700 RPM
Normal Oil Pressure Pounds: 35
TUNE UP SPECIFICATIONS (all models)
Spark Plug Make: AC 46-5
Spark Plug Gap, Inch: .035
Firing Order: 18436572 (front to rear: Right bank 2-4-6-8, left bank 1-3-5-7)
Timing Mark: "A" mark for premiurm fuel; "C" mark for regular fuel; location: Vib. Damper
Engine Idle Speed, RPM: Standard transmission: 450; w/automatic 400 (in drive)
Cylinder Head Torque Lbs.Ft.: 65-70
Compression Pressure & Cranking Speed: 150
Voltage & Polarity: 12 volts, negative ground
PISTON AND RING SPECIFICATIONS
Fitting Pistons with Scale: Pistons removed from above. Shim thickness: .002
Pounds on a Pull Scale: 11
Ring End Gap: In tapered bores, fit rings in tightest portion of ring travel
Compression: .010
Oil: .010
Clearance in Groove: Compression: .0017-0035; Oil: .0015-.003
Wristpin Diameter, Inch: 1.000
VALVE SPECIFICATIONS
Operating Clearance:
Intake: 0 Exhaust: 0
Valve Seat Angle, degrees: 44
Valve Timing: (BTDC = before top dead center; ATDC = after top dead center)
Intake opens: 22 BTDC
Exhaust Closes: 27 ATDC
Valve Spring Pressure Pounds at Inches Length:
Inner Spring: 60 @ 1-11/16
Valve Stem Clearance: Intake: .0005-.0025; Exhaust: .001-.0025
ENGINE BEARING SPECIFICATIONS
Connecting Rod Bearings:
Journal Diameter, Inches: 2.2488-2.2493
Bearing Clearance, Inch: .0005-.002
Rod End Play, Inch: .008-.014
Rod Bolt Tension: Lbs.Ft.: 40-45
Main Bearings:
Journal Diameter, Inches: 2.4990-2.4995
Bearing clearance: .0008-.0025
Shaft End Play: .001-.005 (Thrust on Rear Bearing)
Main Bolt Tension: Lbs.Ft.: 90-100
CAPACITY DATA
Cooling System:
Without heater: 19-3/4 quarts
With heater: 20-3/4 quarts
Fuel Tank: 20 gallons
Engine Oil: 5 quarts
Transmission: w/out overdrive: 2-1/2 pints; Automatic: 12 quarts
Rear Axle: 5 pints
DELCO-REMY DISTRIBUTOR SPECIFICATIONS
Distributor part number: 1110835 (distributor rotates counter-clockwise)
Cam Angle, degrees: 26-33
Breaker Point opening, Inch: .016
Condenser Capacity: .18-.23 Mfds.
Breaker Arm Spring Tension: 19-23 Oz.
Centrifugal Advance: (degrees at RPM of distributor)
Advance starts: 1-1/2 @ 500 RPM
Full Advance: 12 @ 1950 RPM
Inches of Vacuum to Start Plunger Movement: 6-1/2 - 9
Inches of Vacuum for Full Plunger Movement: 16-1/2
Maximum Vacuum Advance Dist., Degrees: 14
DELCO-REMY GENERATOR SPECIFICATIONS
Generator Number: 1102002 (generator rotates clockwise, 12 volts, Negative Ground)
Generator output: 30 amps @ 2150 RPM
Brush Spring Tension: 28 oz.
DELCO-REMY REGULATOR SPECIFICATIONS
Regulator Number: 1118750
Cutout Relay:
Voltage to close points: 12.8
Reverse current to open points: 0-4
Voltage Regulator Setting: 14.5 volts
Current and Voltage Armature Air Gap: .075 inches
Current Regulator Setting: 30 amps
DELCO-REMY STARTING MOTOR SPECIFICATIONS
Part number: 1107602 (rotates clockwise)
Bush Spring Tension, Ounces: 24-28
No Load Test: 75 amps, 10.3 volts @ 6500 RPM
Torque Test: 460 Amps, 5.20 volts, Torque, Lbs.Ft.: 11.5
WHEEL ALIGNMENT SPECIFICATIONS
Caster, Degrees
Limits: -1/2 to +1/2
Desired: 0
Camber, Degrees
Limits: -3/8 to +3/8
Desired: 0
Toe-In, Inches: 1/16 to 1/8
Toe-Out on Turns, Degrees: (If toe-out is incorrect, when other adjustments are correct, look for bent steering arms.)
Outer wheel: 20
Inner Wheel: 24-1/2 to 25-1/2; Model 75: 23-1/2 to 24-1/2
Kingpin Angle, or Steering Axis Degrees: (If king pin or spindle support angle are incorrect, but camber is correct, look for bent suspension arms or steering knuckle support)
5-5/6 @ 04 Camber

1954
Engine Specifications: 1954 Cadillac 331 V8
GENERAL SPECIFICATIONS
Model Designation: Series 60, Series 62, Series 75
Wheel base: Series 60: 133; Series 62: 129; Series 75: 149-3/4
Valve Location: In head
Bore and Stroke: 3-13/16 x 3-5/8
Piston displacement, Cubic Inches: 331.0
Compression ratio: 8.25
Maximum Brake Horsepower: 230 @ 4400 RPM
Maximum Torque Lbs.Ft. @ RPM: 330 @ 2700 RPM
Normal Oil Pressure Pounds: 35
TUNE UP SPECIFICATIONS (all models)
Spark Plug Make: AC 46-5
Spark Plug Gap, Inch: .035
Firing Order: 18436572 (front to rear: Right bank 2-4-6-8, left bank 1-3-5-7)
Timing Mark: "A" mark for premiurm fuel; "C" mark for regular fuel; location: Vib. Damper
Engine Idle Speed, RPM: w/automatic 400 (in drive)
Cylinder Head Torque Lbs.Ft.: 65-70
Compression Pressure & Cranking Speed: 150
Voltage & Polarity: 12 volts, negative ground
PISTON AND RING SPECIFICATIONS
Fitting Pistons with Scale: Pistons removed from above. Shim thickness: .002
Pounds on a Pull Scale: 11
Ring End Gap: In tapered bores, fit rings in tightest portion of ring travel
Compression: .010
Oil: .010
Clearance in Groove: Compression: .0017-0035; Oil: .0015-.003
Wristpin Diameter, Inch: 1.000
VALVE SPECIFICATIONS
Operating Clearance:
Intake: 0 Exhaust: 0
Valve Seat Angle, degrees: 44
Valve Timing: (BTDC = before top dead center; ATDC = after top dead center)
Intake opens: 22 BTDC
Exhaust Closes: 27 ATDC
Valve Spring Pressure Pounds at Inches Length:
Inner Spring: 60 @ 1-11/16
Valve Stem Clearance: Intake: .0005-.0025; Exhaust: .001-.0025
ENGINE BEARING SPECIFICATIONS
Connecting Rod Bearings:
Journal Diameter, Inches: 2.2488-2.2493
Bearing Clearance, Inch: .0005-.002
Rod End Play, Inch: .008-.014
Rod Bolt Tension: Lbs.Ft.: 40-45
Main Bearings:
Journal Diameter, Inches: 2.4990-2.4995
Bearing clearance: .0008-.0025
Shaft End Play: .001-.005 (Thrust on Rear Bearing)
Main Bolt Tension: Lbs.Ft.: 90-100
CAPACITY DATA
Cooling System:
Without heater: Series 60, 62: 19-3/4 quarts; With heater: 22 quarts
Without heater: Series 75: 19-3/4 quarts; With heater: 24-1/2 quarts
Fuel Tank: 20 gallons
Engine Oil: 5 quarts
Transmission: Automatic: 12 quarts
Rear Axle: 5 pints
DELCO-REMY DISTRIBUTOR SPECIFICATIONS
Distributor part number: 1110844 (distributor rotates counter-clockwise)
Cam Angle, degrees: 26-33
Breaker Point opening, Inch: .016
Condenser Capacity: .18-.23 Mfds.
Breaker Arm Spring Tension: 19-23 Oz.
Centrifugal Advance: (degrees at RPM of distributor)
Advance starts: 1-1/2 @ 500 RPM
Full Advance: 12 @ 1950 RPM
Inches of Vacuum to Start Plunger Movement: 6-1/2 - 9
Inches of Vacuum for Full Plunger Movement: 16-1/2
Maximum Vacuum Advance Dist., Degrees: 14
DELCO-REMY GENERATOR SPECIFICATIONS
Generator Number: 1102002 (generator rotates clockwise, 12 volts, Negative Ground)
Generator output: 30 amps @ 2150 RPM
Brush Spring Tension: 28 oz.
DELCO-REMY REGULATOR SPECIFICATIONS
Regulator Number: 1118750
Cutout Relay:
Voltage to close points: 12.8
Reverse current to open points: 0-4
Voltage Regulator Setting: 14.5 volts
Current and Voltage Armature Air Gap: .075 inches
Current Regulator Setting: 30 amps
DELCO-REMY STARTING MOTOR SPECIFICATIONS
Part number: 1107622 (rotates clockwise)
Bush Spring Tension, Ounces: 30-40
No Load Test: 95 amps, 10.1 volts @ 3500 RPM
Torque Test: 460 Amps, 5.2 volts, Torque, Lbs.Ft.: 11
WHEEL ALIGNMENT SPECIFICATIONS
Caster, Degrees
Limits: 0 to -1
Desired: -1/2
Camber, Degrees
Limits: -3/8 to +3/8
Desired: 0
Toe-In, Inches: 3/16 to 1/4
Toe-Out on Turns, Degrees: (If toe-out is incorrect, when other adjustments are correct, look for bent steering arms.)
Outer wheel: 20
Inner Wheel: 23
Kingpin Angle, or Steering Axis Degrees: (If king pin or spindle support angle are incorrect, but camber is correct, look for bent suspension arms or steering knuckle support)
5-5/6 @ 04 Camber

1955
Engine Specifications: 1955 Cadillac 331 V8
GENERAL SPECIFICATIONS
Model Designation: Series 60, Series 62, Series 75
Wheel base: Series 60: 133; Series 62: 129; Series 75: 149-3/4
Valve Location: In head
Bore and Stroke: 3-13/16 x 3-5/8
Piston displacement, Cubic Inches: 331.0
Compression ratio: 9.1
Maximum Brake Horsepower: 250 @ 4600 RPM; Eldorado 270 @ 4800
Maximum Torque Lbs.Ft. @ RPM: 345 @ 2800 RPM; Eldorado 345 @ 3200
Normal Oil Pressure Pounds: 35
TUNE UP SPECIFICATIONS (all models)
Spark Plug Make: AC 44-5
Spark Plug Gap, Inch: .035
Firing Order: 18436572 (front to rear: Right bank 2-4-6-8, left bank 1-3-5-7)
Timing Mark: "A" mark for premiurm fuel; "C" mark for regular fuel; location: Vib. Damper
Engine Idle Speed, RPM: w/automatic 400 (in drive)
Cylinder Head Torque Lbs.Ft.: 65-70
Compression Pressure & Cranking Speed: 165 min.
Voltage & Polarity: 12 volts, negative ground
PISTON AND RING SPECIFICATIONS
Fitting Pistons with Scale: Pistons removed from above. Shim thickness: .002
Pounds on a Pull Scale: 11
Ring End Gap: In tapered bores, fit rings in tightest portion of ring travel
Compression: .010
Oil: .010
Clearance in Groove: Compression: .0017-0035; Oil: .0015-.003
Wristpin Diameter, Inch: 1.000
VALVE SPECIFICATIONS
Operating Clearance:
Intake: 0 Exhaust: 0
Valve Seat Angle, degrees: 44
Valve Timing: (BTDC = before top dead center; ATDC = after top dead center)
Intake opens: 19 BTDC
Exhaust Closes: 30 ATDC
Valve Spring Pressure Pounds at Inches Length:
Inner Spring: 60 @ 1-11/16
Valve Stem Clearance: Intake: .0005-.0025; Exhaust: .001-.0025
ENGINE BEARING SPECIFICATIONS
Connecting Rod Bearings:
Journal Diameter, Inches: 2.2488-2.2493
Bearing Clearance, Inch: .0005-.002
Rod End Play, Inch: .008-.014
Rod Bolt Tension: Lbs.Ft.: 40-45
Main Bearings:
Journal Diameter, Inches: 2.4990-2.4995
Bearing clearance: .0008-.0025
Shaft End Play: .001-.005 (Thrust on Rear Bearing)
Main Bolt Tension: Lbs.Ft.: 90-100
CAPACITY DATA
Cooling System:
Without heater: Series 60, 62: 18 quarts; With heater: 20-1/3 quarts
Without heater: Series 75: 18 quarts; With heater: 22-4/5 quarts
Fuel Tank: 20 gallons
Engine Oil: 5 quarts
Transmission: Automatic: 12 quarts
Rear Axle: 5 pints
DELCO-REMY DISTRIBUTOR SPECIFICATIONS
Distributor part number: 1110852 (distributor rotates counter-clockwise)
Cam Angle, degrees: 26-33
Breaker Point opening, Inch: .016
Condenser Capacity: .18-.23 Mfds.
Breaker Arm Spring Tension: 19-23 Oz.

Centrifugal Advance: (degrees at RPM of distributor)
Advance starts: 1-1/2 @ 500 RPM
Full Advance: 10 @ 1550 RPM
Inches of Vacuum to Start Plunger Movement: 6 - 8-1/2
Inches of Vacuum for Full Plunger Movement: 15 - 16
Maximum Vacuum Advance Dist., Degrees: 18
DELCO-REMY GENERATOR SPECIFICATIONS
Generator Number: 1102011 (generator rotates clockwise, 12 volts, Negative Ground)
Generator output: 30 amps @ 2150 RPM
Brush Spring Tension: 28 oz.
DELCO-REMY REGULATOR SPECIFICATIONS
Regulator Number: 1118826
Cutout Relay:
Voltage to close points: 12.8
Reverse current to open points: 0-4
Voltage Regulator Setting: 14.5 volts
Current and Voltage Armature Air Gap: .075 inches
Current Regulator Setting: 30 amps
DELCO-REMY STARTING MOTOR SPECIFICATIONS
Part number: 1107629 (rotates clockwise)
Bush Spring Tension, Ounces: 35 min.
No Load Test: 95 amps, 10.1 volts @ 3500 RPM
Torque Test: 470 Amps, 5.2 volts, Torque, Lbs.Ft.: 10-1/2
WHEEL ALIGNMENT SPECIFICATIONS
Caster, Degrees
Limits: 0 to -1
Desired: -1/2
Camber, Degrees
Limits: -3/8 to +3/8
Desired: 0
Toe-In, Inches: 3/16 to 1/4
Toe-Out on Turns, Degrees: (If toe-out is incorrect, when other adjustments are correct, look for bent steering arms.)
Outer wheel: 20
Inner Wheel: 23
Kingpin Angle, or Steering Axis Degrees: (If king pin or spindle support angle are incorrect, but camber is correct, look for bent suspension arms or steering knuckle support)
5-5/6 @ 04 Camber

1956
Engine Specifications: 1956 Cadillac 365 V8
GENERAL SPECIFICATIONS
Model Designation: Series 60, Series 62, Series 75
Wheel base: Series 60: 133; Series 62: 129; Series 75: 149-3/4
Valve Location: In head
Bore and Stroke: 4 x 3-5/8
Piston displacement, Cubic Inches: 365
Compression ratio: 9.75
Maximum Brake Horsepower: 285 @ 4600 RPM; Eldorado 305 @ 4700
Maximum Torque Lbs.Ft. @ RPM: 400 @ 2800 RPM; Eldorado 400 @ 3200
Normal Oil Pressure Pounds: 30-35
TUNE UP SPECIFICATIONS (all models)
Spark Plug Make: AC 44
Spark Plug Gap, Inch: .035
Firing Order: 18436572 (front to rear: Right bank 2-4-6-8, left bank 1-3-5-7)
Timing Mark: "A" mark for premiurm fuel; "C" mark for regular fuel; location: Vib. Damper
Engine Idle Speed, RPM: w/automatic 400 (in drive)
Cylinder Head Torque Lbs.Ft.: 65-70
Compression Pressure & Cranking Speed: 165 min.
Voltage & Polarity: 12 volts, negative ground
PISTON AND RING SPECIFICATIONS
Fitting Pistons with Scale: Pistons removed from above. Shim thickness: .002
Pounds on a Pull Scale: 11
Ring End Gap: In tapered bores, fit rings in tightest portion of ring travel
Compression: .013
Oil: .013
Clearance in Groove: Compression: .0017-0035; Oil: .0008-.0026
Wristpin Diameter, Inch: 1.000
VALVE SPECIFICATIONS
Operating Clearance:
Intake: 0 Exhaust: 0
Valve Seat Angle, degrees: 44
Valve Timing: (BTDC = before top dead center; ATDC = after top dead center)
Intake opens: 22 BTDC
Exhaust Closes: 27 ATDC
Valve Spring Pressure Pounds at Inches Length:
Inner Spring: 65 @ 1.980
Valve Stem Clearance: Intake: .0001-.0025; Exhaust: .001-.0025
ENGINE BEARING SPECIFICATIONS
Connecting Rod Bearings:
Journal Diameter, Inches: 2.2488-2.2493
Bearing Clearance, Inch: .0005-.002
Rod End Play, Inch: .008-.014
Rod Bolt Tension: Lbs.Ft.: 40-45
Main Bearings:
Journal Diameter, Inches: 2.625
Bearing clearance: .0008-.0025
Shaft End Play: .001-.005 (Thrust on Rear Bearing)
Main Bolt Tension: Lbs.Ft.: 90-100
CAPACITY DATA
Cooling System:
Without heater: Series 60, 62: 17-1/4 quarts; With heater: 19-1/4 quarts
Without heater: Series 75: 17-1/4 quarts; With heater: 21-3/4 quarts
Fuel Tank: 20 gallons
Engine Oil: 5 quarts
Transmission: Automatic: 12 quarts
Rear Axle: 5 pints
DELCO-REMY DISTRIBUTOR SPECIFICATIONS
Distributor part number: 1110858, 1110859 (distributor rotates counter-clockwise)
Cam Angle, degrees: 26-33
Breaker Point opening, Inch: .016
Condenser Capacity: .18-.23 Mfds.
Breaker Arm Spring Tension: 19-23 Oz.

Centrifugal Advance: (degrees at RPM of distributor)
Advance starts: 1-1/2 @ 500 RPM
Full Advance: 10 @ 1550 RPM
Inches of Vacuum to Start Plunger Movement: 5-7
Inches of Vacuum for Full Plunger Movement: 15-1/2 - 17-1/4
Maximum Vacuum Advance Dist., Degrees: 18
DELCO-REMY GENERATOR SPECIFICATIONS
Generator Number: 1102002, 1102011 (generator rotates clockwise, 12 volts, Negative Ground)
Generator output: 30 amps @ 2150 RPM
Brush Spring Tension: 28 oz.
DELCO-REMY REGULATOR SPECIFICATIONS
Regulator Number: 1119001
Cutout Relay:
Voltage to close points: 12.8
Reverse current to open points: 0-4
Voltage Regulator Setting: 14.5 volts
Current and Voltage Armature Air Gap: .075 inches
Current Regulator Setting: 30 amps
DELCO-REMY STARTING MOTOR SPECIFICATIONS
Part number: 1107642 (rotates clockwise)
Bush Spring Tension, Ounces: 35
No Load Test: 91 amps, 10.6 volts @ 3240 RPM
Torque Test: 385 Amps, 3.5 volts
WHEEL ALIGNMENT SPECIFICATIONS
Caster, Degrees
Limits: 0 to -1
Desired: -1/2
Camber, Degrees
Limits: -3/8 to +3/8
Desired: 0
Toe-In, Inches: 5/32 to 7/32
Toe-Out on Turns, Degrees: (If toe-out is incorrect, when other adjustments are correct, look for bent steering arms.)
Outer wheel: 20
Inner Wheel: 22-2/3
Kingpin Angle, or Steering Axis Degrees: (If king pin or spindle support angle are incorrect, but camber is correct, look for bent suspension arms or steering knuckle support)
5-5/6 @ 04 Camber