kust saab teada exp id koode?
kust saab teada exp id koode?
Tere kõik cadillaaci omanikud. olen uus kasutaja ja soetasin endale ka cadillac sts 2001 a. aga tahaks teada mis tähendavad kõik need koodid. EXP ID? ei saa saksa keelest aru.. aitäh abistajatele..
Re: kust saab teada exp id koode?
need ongi tavaliselt ainult kasutaja manuaalis olemas.
üks võimalus on aju ümber programmeerida USA omaks, siis räägib sulle kõik kenasti inglise keeles ära.
Aga ega ma ei mäleta, kas seda 01 aasta autoga ise teha sai. uurin asja natuke.
üks võimalus on aju ümber programmeerida USA omaks, siis räägib sulle kõik kenasti inglise keeles ära.
Aga ega ma ei mäleta, kas seda 01 aasta autoga ise teha sai. uurin asja natuke.
„siin on tegemist jällegi ühe toreda riigireetmisega“ (Bretschneider).
Re: kust saab teada exp id koode?
paraku jah, saad seda tega Vikingis, sest seal on Tech II seade olemas.
NOTES
THIS ONLY WORKS FOR THE FOLLOWING MODELS!!!
96-02 Eldorado, ETC, ESC
96-97 Seville, STS, SLS
96-99 Deville, Concourse, DeElegance
~~~~~TO ADD COOLANT AND MPH DIC MESSAGE~~~~~
1) Press the OFF and PASS WARMER (referred to from here as WARMER) buttons simultaneously to enter diagnostic mode.
2) Let the system read any codes it has stored. You will ultimately be presented with "PCM?". You will answer with the fan speed control button. UP = yes and DOWN = no.
3) Press DOWN until you are presented with "IPC?". On mine, it's the very next prompt. When you get to the "IPC?" prompt, press UP to enter the IPC area (Instrument Panel Cluster).
4) Press DOWN until you are presented with "IPC OVERRIDE?". Press UP to enter the override area.
5) Scroll down (with the DOWN button) until you get to Option E. Wait a second or two, and the override value will appear to the right where the TRIP ODOMETER normally reads. Yours will probably read "43". That's what mine read when I first did this.
Below are the Option E values:
- Coolant Temp message (64)
- Battery Volts message (32)
- Engine RPM message (16)
- Avg Mph message (8)
- Mph message (4)
- Fuel Used message (2)
- Inst Mpg message (1)
The stock displays (for analog E/K displays) are Battery Volts, Avg Mph, Fuel Used, and Inst Mpg, for a total value of "43".
6) Use the WARMER button to increment the value of the override. In this case, we want to add Coolant Temp, so we're going to add "64" to "43", or "107". Press the WARMER button repeatedly to increment the value from "43" to "107".
If you make a mistake, you can decrement the value by pressing the COOLER button.
7) To permanently save the new value, hold the FRONT DEFROST and the A/C buttons simultaneously until the new override value flashes once.
8) You're done. Press OFF repeatedly to "back out" of the diagnostic system. You'll probably need to press OFF 5 or 6 times to get out of the deep "menu structure" you're in now.
Now, the coolant temp (in units specified) should be one "stop" along the revolving door we call the DIC. If you are in metric units, the coolant temp will read in *C. If you are in standard units, it'll read in *F.
~~~~~TO SHUT OFF DRLS~~~~~
1-4 FOLLOW ABOVE DIRECTIONS!!!
5) Scroll down (with the DOWN button) until you get to Option C. Wait a second or two, and the override value will appear to the right where the TRIP ODOMETER normally reads.
Below are the Option C values:
IPS03 Option C
- RSS installed (128)
-Premium Unleaded Fuel Only -
-Graphic supression (digital) (64)
-Daytime running lamps enabled (32)
-Cellular Telephone Installed (16)
-BTSI message suppression (4)
-Options not set (2)
-FUEL LEVEL LOW message suppresion (1)
6) Use the COOLER button to decrease the value of the override. In this case, we want to remove the DRLs so subtract your number by 32
If you make a mistake, you can decrement the value by pressing the WARMER button.
7) To permanently save the new value, hold the FRONT DEFROST and the A/C buttons simultaneously until the new override value flashes once.
8) You're done. Press OFF repeatedly to "back out" of the diagnostic system. You'll probably need to press OFF 5 or 6 times to get out of the deep "menu structure" you're in now.
NOTE!!!!
in order for your drls to ACTUALLY BE OFF your twilight must be pushed all the way to the left and your fog lights (when applicable) must be off as well!!!
NOTES
THIS ONLY WORKS FOR THE FOLLOWING MODELS!!!
96-02 Eldorado, ETC, ESC
96-97 Seville, STS, SLS
96-99 Deville, Concourse, DeElegance
~~~~~TO ADD COOLANT AND MPH DIC MESSAGE~~~~~
1) Press the OFF and PASS WARMER (referred to from here as WARMER) buttons simultaneously to enter diagnostic mode.
2) Let the system read any codes it has stored. You will ultimately be presented with "PCM?". You will answer with the fan speed control button. UP = yes and DOWN = no.
3) Press DOWN until you are presented with "IPC?". On mine, it's the very next prompt. When you get to the "IPC?" prompt, press UP to enter the IPC area (Instrument Panel Cluster).
4) Press DOWN until you are presented with "IPC OVERRIDE?". Press UP to enter the override area.
5) Scroll down (with the DOWN button) until you get to Option E. Wait a second or two, and the override value will appear to the right where the TRIP ODOMETER normally reads. Yours will probably read "43". That's what mine read when I first did this.
Below are the Option E values:
- Coolant Temp message (64)
- Battery Volts message (32)
- Engine RPM message (16)
- Avg Mph message (8)
- Mph message (4)
- Fuel Used message (2)
- Inst Mpg message (1)
The stock displays (for analog E/K displays) are Battery Volts, Avg Mph, Fuel Used, and Inst Mpg, for a total value of "43".
6) Use the WARMER button to increment the value of the override. In this case, we want to add Coolant Temp, so we're going to add "64" to "43", or "107". Press the WARMER button repeatedly to increment the value from "43" to "107".
If you make a mistake, you can decrement the value by pressing the COOLER button.
7) To permanently save the new value, hold the FRONT DEFROST and the A/C buttons simultaneously until the new override value flashes once.
8) You're done. Press OFF repeatedly to "back out" of the diagnostic system. You'll probably need to press OFF 5 or 6 times to get out of the deep "menu structure" you're in now.
Now, the coolant temp (in units specified) should be one "stop" along the revolving door we call the DIC. If you are in metric units, the coolant temp will read in *C. If you are in standard units, it'll read in *F.
~~~~~TO SHUT OFF DRLS~~~~~
1-4 FOLLOW ABOVE DIRECTIONS!!!
5) Scroll down (with the DOWN button) until you get to Option C. Wait a second or two, and the override value will appear to the right where the TRIP ODOMETER normally reads.
Below are the Option C values:
IPS03 Option C
- RSS installed (128)
-Premium Unleaded Fuel Only -
-Graphic supression (digital) (64)
-Daytime running lamps enabled (32)
-Cellular Telephone Installed (16)
-BTSI message suppression (4)
-Options not set (2)
-FUEL LEVEL LOW message suppresion (1)
6) Use the COOLER button to decrease the value of the override. In this case, we want to remove the DRLs so subtract your number by 32
If you make a mistake, you can decrement the value by pressing the WARMER button.
7) To permanently save the new value, hold the FRONT DEFROST and the A/C buttons simultaneously until the new override value flashes once.
8) You're done. Press OFF repeatedly to "back out" of the diagnostic system. You'll probably need to press OFF 5 or 6 times to get out of the deep "menu structure" you're in now.
NOTE!!!!
in order for your drls to ACTUALLY BE OFF your twilight must be pushed all the way to the left and your fog lights (when applicable) must be off as well!!!
„siin on tegemist jällegi ühe toreda riigireetmisega“ (Bretschneider).
Re: kust saab teada exp id koode?
heres all the option values in the event anyone wants to play with them for any reason
IPS01 Option A
-Universal Theft Deterrent enabled (8)
-Personalization / Memory Installed (4)
-Interior Purge enabled (1)
IPS02 OPtion B ( EXport Country)
-Eropean Economic Community (EEC) (16)
-Japan (8)
-Saudi Arabia (4)
-Canada (2)
-Norway/ Sweden (1)
IPS03 Option C
-RSS installed (128)
-Premium Unleaded Fuel Only Graphic supression [DIGITAL ONLY] (64)
-Daytime running lamps enabled (32)
-Cellular Telephone Installed (16)
-BTSI message suppression (4)
-Options not set (2)
-FUEL LEVEL LOW message suppresion (1)
IPS04 Option D (HVAC Options)
-Afterblow enabled (128)
-De-Ice Installed (64)
-Timer Recirc enabled (16)
-Dual Zone HVAC Installed (8)
Below are the Option E (DIC features)
- Coolant Temp message (64)
- Battery Volts message (32)
- Engine RPM message [DIGITAL ONLY] (16)
- Avg Mph message (8)
- Mph message (4)
- Fuel Used message (2)
- Inst Mpg message (1)
IPS01 Option A
-Universal Theft Deterrent enabled (8)
-Personalization / Memory Installed (4)
-Interior Purge enabled (1)
IPS02 OPtion B ( EXport Country)
-Eropean Economic Community (EEC) (16)
-Japan (8)
-Saudi Arabia (4)
-Canada (2)
-Norway/ Sweden (1)
IPS03 Option C
-RSS installed (128)
-Premium Unleaded Fuel Only Graphic supression [DIGITAL ONLY] (64)
-Daytime running lamps enabled (32)
-Cellular Telephone Installed (16)
-BTSI message suppression (4)
-Options not set (2)
-FUEL LEVEL LOW message suppresion (1)
IPS04 Option D (HVAC Options)
-Afterblow enabled (128)
-De-Ice Installed (64)
-Timer Recirc enabled (16)
-Dual Zone HVAC Installed (8)
Below are the Option E (DIC features)
- Coolant Temp message (64)
- Battery Volts message (32)
- Engine RPM message [DIGITAL ONLY] (16)
- Avg Mph message (8)
- Mph message (4)
- Fuel Used message (2)
- Inst Mpg message (1)
„siin on tegemist jällegi ühe toreda riigireetmisega“ (Bretschneider).